The Fence – Part 8 of 8

The Final Fence Post

I headed to LeVahn Brothers with a sample of what I was dealing with (hookup wire and irrigation tubing) and explained what happened (broken string, broken rope, stuck wires) and came home with some wire pulling lube and a better rope.

We were also back to a weekend so Nate could help. It went much faster with two people, one person operating the shop-vac on one end and the other handling the string on the other. We got the string through quickly and tied it to our new rope and got that all the way through. Then we tied the rope to the hookup wire, once again using the staggered approach, rope to ground hookup wire, then further down added the hot hookup wire. Then we lubed up the wire and Nate started pulling on one end while I pushed on the other. Slowly, but steadily, we made progress; though there was definitely a point where it became far more difficult, and it was about the same point where the rope had broken. We actually dug up the trench there to see if something had kinked the tube but from the outside it seemed find so we kept at it. Nate keeps pulling and I keep pushing. Then the rope breaks free from the hook-up wire. **** **** **** **** (This whole putting up a fence saga sure was stretching my vocabulary.)

Try, try, try, try again. Pull the string through, pull the rope through, attach that rope to that hookup wire like someone’s life depends on it; tape is cheap, use the whole roll! Nate pulls, I push, and slowly, so slowly, through it goes. We have the wire through the tube!

Now we need to connect the ground hookup wire to the ground rods and the hot hookup wire to the fence itself. I was smart enough to spray paint one roll of hookup wire blue so that we would know which was the ground line and which was the hot line. The next tricky part was getting one continuous line of hookup wire to connect all three ground rods to the energizer. The directions were very clear; it could not be three separate pieces of hookup wire, it had to be one continuous run of hookup wire. That meant we had to strip the insulation off the middle of the wire. That is not easy to do, and of course the video did not show that part; the wire was already conveniently stripped. Wire strippers are designed to cut the insulation and then you just pull it off the end, but when you are in the middle of the wire you can’t pull it off, you need to basically filet it off; very carefully, without hurting the wire, or yourself. We failed on both counts. The first effort was Nate’s. He did manage to get the insulation off, but not without damaging the wire, and in the end it snapped. **** That meant pulling more hookup wire through, though that turned out to be fine since we needed enough hookup wire to do all three of the hot lines of the fence anyway. The second effort was mine. Almost immediately I managed to stab myself in the finger, right through my work glove (picture if you like pictures of injuries). Luckily it was bleeding a lot so I was pretty sure the risk of infection was low; and somehow, despite having a white shirt on, I only got blood on my pants, the cardboard I was working on, the driveway, and the garage floor – my white shirt is still white! Nate had been using the string trimmer at the time with ear protection on so I hadn’t even tried to get his attention knowing he would be done fairly soon. As he’s opening the door to the mudroom he is asking “How did you spill red paint by your shoes?” Then he sees me with my hand in the air (trying to keep it above my heart to stop the bleeding long enough to wash it) and is like “Oooooohhhhhh, that’s not paint.”

We took a brief break but opted not to seek medical attention and went back out to finish this ****ing fence. I was far more careful this time and managed to get the insulation off without injuring myself or the interior wire! With that we attached the ground hookup wire to the ground rods and attached the hot hookup wire directly to the top line of ElectroBraid. Then we used a short piece of hookup wire to connect the top line of fence to the second from the bottom line of fence, and then another short piece to connect the second from the bottom line to the bottom line. Then another piece of hookup wire to attach the second from the top line of ElectroBraid to the closest ground rod (we opted for a hot/ground system because that was recommended in places where the ground freezes or when there are drought concerns.) Then we had to dig a trench under the fence to lay hookup wire below it to get electricity from one side of the gate to the other (I let Nate dig that trench, 115 feet of trench digging was enough for me – plus you know, the stab wound). One option for that is to just do a single piece of hookup wire that connects all three hot lines on one side to all three hot lines on the other, and then do a second hookup wire to connect the ground line on one side to the ground line on the other; however according to the internet (which is never wrong) the possible issue with that is if something goes wrong with one line of the fence it can affect all of them, whereas if you connect top to top, middle to middle, etc. and something goes wrong with one line, or you need to disconnect one of the lines for some reason, it won’t impact the other lines of fence. We decided to go with the top to top, middle to middle, etc. option. By this point I was an expert at getting wires through tubes and it was only a 12-foot tube to get under the gate and up on each side, so I managed that on my own all in one day!

Once everything was wired on the fence side, we had to get the hookup wires attached to the energizer which was in the garage. This involved drilling two small holes in the side of our garage which neither of us felt super comfortable doing, but we did it. Hopefully we didn’t mess anything up too badly; we used a LOT of silicone sealer.

We used a lot of silicone sealer, we are both paranoid about putting a hole in our wall. The bricks are holding up the end of the irrigation tubing which is folded over to prevent water from running down it. That also didn’t go as well as the directions implied. 

We still need to patch up the drywall on the inside but that is low on my priority list. Wondering why there is so much masking tape? That’s because we don’t know what we’re doing and it took a few tries to get the hookup wire through the wall.

We attached the hot hookup wire to the hot terminal and the ground hookup wire (thank goodness for the blue paint) to the ground terminal and plugged the energizer in. We officially have an electric fence!

I went around with the voltage tester and it seems like we have a decent charge all along the fence. There was some concern because of how far the various parts of the fence are from one another and the house is in between them, but according to the voltage tester everything seems to be working. Also, according to my hand, which got shocked when I went to fasten the gate. We really need better gate closures.